VISUAL PRESENTERINSTRUCTION MANUALPlease read this instruction manual carefully before using this Visual Presenter and keep it for futurereference.
92. WIRELESS REMOTE CONTROLPoint the infrared emitting part of the wireless remote control unit at the infrared sensor of the Presenter, located on th
103. SETTING UP(1) Raise the column.Raise up the column once, and fall it until it islocked.Note: The lighting arm (L) cannot beindependently raised.N
11Connection to the monitor TVNote: Be sure to turn OFF the power supply to all equipment before making any connections to protect the Presenterand al
124. OPERATION PROCEDURES(1) Turn ON the power switch.Note: Before turning ON the power switch,connection to the monitor should have beencompleted.Not
13When the camera head arm is turned as shown in theright figure, material outside the stage can bephotographed. When the camera head unit is set in t
14Storing the Presenter(4) Fall the lighting arm (R) unit, and turn the camera headto the position shown in the right figure (the positionwith the cam
155. VARIOUS FUNCTIONSLightingThe lighting for presenting printed matter or othermaterial is installed on standard.Each time the lighting button [LAMP
16FocusAuto FocusTo operate Auto-Focus, press the auto focus button[AF] on the front operation panel or wireless remotecontrol, and the Auto-Focus wil
17TELEFARNEARWIDEIRISAFZOOMFOCUSRemote controlPowered Manual FocusTo focus on any part of the material, such as 3-Dmaterial, press the focus button [N
18Color/B&W selectionTo present the B&W (Black&White) material such asdocuments in sharper image with no color blur on themonitor, set to
1IMPORTANT SAFEGUARDSRead Instructions – All the safety and operatinginstructions should be read before the appliance isoperated.Retain Instructions –
196. RS-232C SPECIFICATIONSThe Presenter can be controlled by a PC connected to the Presenter through the RS-232C terminal [RS-232C].Setting up(1) Con
20Cable connectionRS-232C connector specifications (DSUB-9P)Pin No.12345678CodeCDRXDTXDDTRSGDSRRTSCTSNameCarrier DetectReceived DataTransmitted DataDa
21Note: " " in the data column means that SPACE [20H] should be transmitted twice.Table of the communication commandsWhen the electronic ima
22Data format specificationsThis command is executed in the form of 1-command/1 packet. The next command is not accepted until the previousprocessing
23Transmission specifications· Full duplex start-stop sync. mode· Start bit : 1 bit· Data bit : 8 bits· Stop bit : 1 bit· Parity bit : None· X paramet
If the trouble still remains after checking the above, consult your dealer or an authorized ELMO servicecenter.247. TROUBLESHOOTING HINTSSymptomPossib
25GeneralCamera8. SPECIFICATIONSItemSpecificationsPower sourceRated currentAC outlet1 pce. (Max. 400W/Unswitched)AC120V 60Hz0.5AOutside dimensions5
26LightingSupplied accessoriesNote: The specifications are subject to change without notice.Dimensions and weight are approximate.Trademark Acknowledg
WARNING:Unauthorized recording of copyrighted slide films, materials,photographs, etc. may infringe on the rights of copyright owners andbe contrary t
2Damage Requiring Service – Unplug this productfrom the wall outlet and refer servicing to qualifiedservice personnel under the following conditions:W
3Use the Visual Presenter under the rated electrical conditions and TV system.Do not leave the Presenter under direct sunlight or by heaters, or the P
41. PART NAMES AND FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Appearance. . . . . . . . . . . . . . .
51. PART NAMES AND FUNCTIONSAppearance1. Stage2. Column3. Camera Head4. Close-up Lens Holder6. Lighting Arm (L)7. Front Operation Panel8. Remote Contr
6Name FunctionReference Page11 Zoom Buttons To change the image size.12 Auto Focus Button To focus automatically (One-shot auto focus).Front Operation
Button Name FunctionReference Page18 2X To double the image size.19 Directions To scroll the enlarged image.When this key is pressed while the image i
850 60Camera Head and ColumnDC12V32. Output TerminalName FunctionReference Page31. Shutter Selection Switch To set the shutter time. In an areawhere p
Comments to this Manuals