16mm CHANNEL LOAD/Ne ~O[JfD ··.PBOJECTOB IG-Cl/IG-CL . OPTICAL 1 Instruction Manual
8 Projection o Turn the master control switch clockwise to ffJ ,then turn it further to (]~ , and the lamp is switched on and simultaneously the pr
Various, projections .Quick review This feature is used to see specific frames you wish to review. Turn the control switch counter clock-wise from a~
10 • When using extension speaker I n the event you have occassion to use an accessory extension speaker for a large audience in a large audito
• Public address system You can utilize your ELMO sound projector as a public address system during projection when an accessory microphone is inser
12 Rewinding • When the projection is completed, rewind the film as follows. o I nsert the film end into the slot of the front reel hub. @ Turn the
(,I Maintenance Clean the film channel and lens prior to projection; accumulation of dust and film particles in the film channel gate will scratct
To install the cover, align the framing knob with the cover notch and the guide pins at the upper left and lower right with the corresponding holes a
Use the stiff cleaning brush (supplied) to clean film channel gate, then wipe clean with lint-free cloth. After the cleaning is over, align the
16 • Cleaning projection lens To remove the projection lens, pull it out straight while pulling the focusing knob toward yourself. To remove the dus
Replacing lamp and fuse BE SURE TO DISCONNECT THE POWER CORD WHEN REPLACING LAMP AND FUSE . • Replacing projection lamp The type of projection lam
IMPORTANT SAFEGUARDS W hen using your photographic equipment, basic safety pre-cautions should always be followed, including the following
18 To replace a new lamp, push it into the socket as shown in the picture. At this time, be sure to insert the lamp firmly into its socket. If i
• Replacing fuse To remove the fuse holders, turn the holder heads counterclockwise with a Philips head screwdriver. Exciter lamp fuse Amplifier
20 Trouble-shooting hints When the motor fails to operate: • Check the power cord for proper connection. • Check the power (main) fuse for blow-out
When changing the projection speed from 24 fps to 18 fps or to change electric current cycles (50Hz -60Hz) • The projector is originally fixed for 24
22 Accessories This lens is used for projecting Cinemascope movies. It can be installed in front of the projection lens simply by mounting it on th
! • Wide-angle projection lens F1.4 20mm • Conversion lens • Zoom converter This wide-angle lens is designed for projection in a small room. Thi
24 • Twin extension speakers ES-1000 High performance extension speakers with a 10" (25 cm) woofer and a twe-eter. Stores conveniently in one
Exciter lamp Amplifier Specifications MUsiqJoWer OllltPlilt TOfle eOfltrol Pubilfu address system Speeifieatiofls afld desigfls are slIIbject to chaf
EIf1.9 ELMO CO.,LTD. 6, Kamiho-dori 1-chome, Mizuho-ku, Nagoya, 467, JAPAN Tel. 052-811-5131 Fax. 052-811-5142 OVERSEAS SUBSIDIARY COMPANIES U.S.A.
Congratulations and thank you on joining the large nation-wide family of ELMO 16-CL sound projector owners. You have selected a precision-engineer
2 Major parts descriptions Reel lock ------~ Take-up reel arm --------...: Folding button for take-up reel arm--------------i Front cover--------
~~!!!~-----Reel lock '1-------Feed reel arm :---------Folding button for feed reel arm ,.-------Slot-in roller ------Threading guide No. 1 --
o 4 Preparation for projection Set up your projector and screen properly. For steady projection, place the projector on a sturdy support at right ang
Install the take-up reel 240m (800ft.), which is stored on the rear of the projector, on the rear reel spindle. The reel capacity of the projector
6 Film threading O Hold the tip of the film leader between thumb and index finger -then pull the leader first through the slot-in roller, next over
After the film threading is completed, wind the leader on the take-up reel. Make sure the fi 1m is properly threaded through the channel by turning
Comments to this Manuals