PAN • TILT • ZOOM COMMUNICATION CAMERAPTC-100SPTC-110RINSTRUCTION MANUALPlease read this instruction manual carefully before using the PTC-100S orPTC-
- 9 -Connection examples for the Camera3. SETTING UPDC IN 12VVIDEOS-VIDEOIN RS-232C OUTPCPTC-100S/110RAC/DC adapter (Included)MonitorVIDEO CABLE(Incl
- 10 -Note: When carrying the Camera, be sure to hold the base.Note: Do not turn the Camera head in the PAN-TILT direction by hand, orthe Camera head
- 11 -•Make 4 holes of 8mm (5/16 in.) to theCeiling Tile as shown.70mm (2-3/4 in.)102mm (4 in.)54mm(2-1/8 in.)FRONTBACKCEILING TILE(t 1/2 in. 1 in
- 12 -HEXAGON HEAD BOLT M5x40 (supplied), 4 PCSMAIN UNITCEILING PLATEWING NUT M5 (supplied), 4 PCSMOUNTING HOLE: 5/16 in., 4 LOCATIONSCEILING TILE
- 13 -CEILING PLATECEILING TILESAFETY WIRE LOOPING HOLESAFETY WIRE (not supplied)• Loop up one end of the Safety Wires throughthe respective safety wi
- 14 -[1] Power supply to the CameraThe Camera has no POWER switch. Power is supplied to the Camera when the AC adapter is connected to the wall socke
- 15 -[3] Operating PAN/TILT• While watching the screen, press any of (UP, DOWN, LEFT, RIGHT)direction buttons for the direction in whichyou want to w
- 16 -[4] Lens operation(1) Zoom operation• The object is zoomed in (appears larger in thescreen) when TELE button of ZOOM ispressed, or zoomed out
- 17 -[5] BLC (Back Light Control)In case the back lighting is too bright to shoot themain object clearly, press BACK LIGHTbutton.To cancel this mode
- 18 -5. THE ID NUMBER SETTINGWhen multiple Cameras are laid out adjacently and operated via the wireless remotecontroller, the Cameras receiving the
1. Read these instructions.2. Keep these instructions.3. Heed all warnings.4. Follow all instructions.5. Do not use this apparatus near water.6. Clean
- 19 -6. OSD (On-Screen Display)The MENU button is used to turn ON/OFFthe OSD display. When the hierarchy menu isdisplayed, the screen goes back to t
- 20 -(1) CAMERA SETUP SELECT ADJUST (Return to MENU )12<1> BLC<2> AGC<3> AP GAIN<4> FL<5> NEXT PAGE<6> ME
- 21 -(3) TITLE SETSELECT ADJUST(Return to MENU )12<1> MOTOR SPEED<2> SPEED<3> L/R DIRECTION• To set the title for each preset posi
- 22 -7. DIP SWITCH SETTINGSThe PAN-TILT settings, the LENS settings, the preset settings, the ID settings and theCamera settings by means of the OSD
- 23 -The Camera can be controlled from the PC by connecting the RS-232C terminal to the PC.Note: Before starting the connection work, be sure to turn
- 24 -9. TROUBLESHOOTING HINTSIf the trouble still remains after checking the above, consult your nearest dealer orauthorized ELMO service center. Sym
- 25 -10. SPECIFICATIONSGeneralCameraItem SpecificationsPower source 12V DCCurrent consumption Max. 1AOutside dimensions 124mm(W) X 153mm(D) X 136mm(H
- 26 -11. SUPPLIED ACCESSORIESPan/TiltOtherItem SpecificationsPan mechanism Left 150° Right150°Tilt mechanism (PTC-100S) Up 90° Down30°(PTC-110R) Up 3
ELMO CO., LTD.6-14, Meizen-cho, Mizuho-ku, Nagoya, 467-8567, JapanOVERSEAS SUBSIDIARY COMPANIESU.S.A Elmo Mfg. Corp.1478 Old Country Road, Plainview,
- 2 -CAUTION• Do not use any power supply otherthan specified.WARNINGTO REDUCE THE RISK OF FIRE ORELECTRIC SHOCK, DO NOTEXPOSE THIS APPLIANCE TO RAINO
Be sure to use the provided AC adapter.Do not leave the Camera under direct sunlight or by heater, or theCamera may be discolored, or damaged.Do not p
- 4 -CONTENTSIMPORTANT SAFETY INSTRUCTIONS ...1HANDLING PRECAUTIONS ...
Overall View- 5 -1. PART NAMES AND FUNCTIONSCAMERA HEADINFRARED SENSORLEDBASES-VIDEO (Mini DIN 4P)COMPOSITE-VIDEO(RCA pin jack)INFRARED SENSORDC INLEN
Wireless Remote Controller- 6 -POWER1OPEN2CLOSE3AUTO (Iris)4NEAR5FAR6AUTO (Focus)7TELE8WIDE9MENU12CURSOR/PAN-TILT13Directions10HOME11ID17RESET15BACK L
Point the infrared emitting part of the wireless remote controller at the infrared sensor of theCamera, located at the front, and the rear panel, and
- 8 -PreparationRemove the battery case cover by pressing downward on the [ ] mark part in the direction as indicated by the arrow.Install 2 pcs. of b
Comments to this Manuals